Archive for the ‘Guitars’ Category

“When last we left our intrepid hero, he had just removed all the electronics from the ’08 Epiphone Les Paul Standard Plain Top.  In today’s exciting episode, we will be captivated as he prepares the guitar to receive the transplant, and creates a new wiring harness from scratch”.

Ok, that may be a bit mellow-dramatic, but I always did love the old radio shows.  Now that I’ve prepped the guitar by removing the old electronics, and I’ve prepped myself by adding a few of my favorite Blue beverages from our Canadian friends, it’s time to create the wiring harness.

One important difference between the harness that I just took out, and the one that I’m about to make is the shaft size of the pots.  Epiphone stock pots have slightly smaller shafts than the CTS pots.  In order for the new pots to fit, we need to enlarge the holes (Gibson uses different pots which require the larger hole, so this is not needed).  Some people have suggested using a reaming tool to enlarge the holes.  I feel that is overkill, since the holes only need to be worked a small fraction of an inch, and I feel the reaming tool may harm the finish (the Epiphone poly finish has a tendency to flake).  I prefer working the holes with 60 and 220 grit sandpaper.  Yes, it takes a bit longer, but the finished product is better.

You’ll need to open up the holes for the pots just ever so slightly. I use 60 and 220 grit sandpaper. Cut a 4×4 inch piece of both grits and roll them up. Put them in the holes and gently work the sandpaper up and down while slowly rotating the sandpaper in the hole. Start with the 60 grit, and constantly check to see if the pot fits. You don’t want to make the holes too big. When the pot just barely doesn’t fit in the hole, finish it off with the 220 grit sandpaper until the pot fits snugly, but is not tight.  Also, you won’t have to worry about hurting the finish.  It’s important to open the holes before you make the harness.  Since we use one of the new pots to check the size of holes as we sand them, you don’t want to move the completed harness around every time you want to check the holes.

The hole directly above the tailpiece has already been finished. You’ll see it looks clean and all the finish has been removed from inside the hole compared to the others.

We need to create a template of the pot holes so we get the spacing right when we build our new harness.  Take a blank piece of paper and tape it to the front of the guitar so the paper covers the holes for the pots.  Flip the guitar over and from inside the electronics cavity use a pen to draw circles on the paper using the holes as a guide.  Make sure you label which pots are neck and bridge, and volume and tone.  Remove the paper from the guitar and tape it to a thin piece of scrap wood.  This will become our template.

With the paper taped to the wood, and using a 3/8” bit, drill 4 holes through the circles on the paper into the wood.  Off to the side, away from the 4 holes you just drilled, drill a ½” hole to mount the toggle switch.

At this point I should probably talk about pot values and placement. Even the best set of matched pots from Jonesy or MSSC won’t all be the same value. Because of this, the experts have figured out where each pot should go. The pot with the highest value should be the neck volume pot to give the pickup as much clarity as possible.  Next should be the bridge volume, then neck tone, and finally bridge tone.  To get the value of a pot, use a multi-meter set to measure resistance.  Put the probes on the outer lugs.  The resistance shown on the multi-meter is the value of the pot.  Matched sets from several vendors will already be labeled with both value and placement, such as “NV” for Neck Volume.  You’ll have to measure the pots yourself if you order the pots from StewMac or Allparts.

Now that we know which pot should go where, put the pots in the holes.  The neck volume lugs should facing the neck tone lugs.  The goes for the bridge pots, too.  Finally, put the toggle switch in the hole. We don’t want anything moving while we have a hot soldering iron it, so put the nuts on the pots and switch and finger tighten everything down. Since we’re all guitar players here, we should have above average finger strength. 🙂

So, before we start soldering wires I’d like to state the obvious (my wife always says I have an amazing grasp of the obvious).  Test every solder joint as soon as you’re done.  Don’t go a few steps and then test.  Test immediately.  It will save you so much time in the end.  Also, make sure you test all the connections.  In places where you are soldering a wire to two lugs at the same time, test both lugs against each other and with the wire.  I cannot stress enough how important it is at this stage to take your time and constantly test, test, test!

I’ve always found it easier to start off slowly, so I wired up the switch first.  In the picture above, the two lugs coming off the left side of the switch will go to the jack.  On the left side, there are two lugs which will connect to the volume pots, and one big loop which is the ground.  Using a pair of pliers, bend the two lugs on the left together (opposite side from the ground), and then solder a 2’ piece of shielded wire to the lugs.  Next, we take 2 more pieces of 2’shielded wire and solder them to the lugs on the opposite side (one to each).  Now that we have the leads soldered to the switch, we need to ground the whole thing.  Since I’m using vintage push-back wire with an exposed braided shield, I took a 6” piece of exposed solid 22 gauge wire and soldered it to the grounding lug.  Then I wrapped the other end around the braided shielding of the 3 wires coming off the switch and soldered it to shielding.  While we are testing the switch to make sure it works as it should, it’s a good idea to label the wires for future reference (Neck, Bridge, Jack are the labels I use).

JonesyBlues has a great video on how to solder the switch as well (which is another reason why I like doing business with him).

With the switch done, and the soldering iron ready to go, I moved on to wiring up the pots with the caps and ground loop.  Since we’ll be soldering to the back of the pots, now is a good time to switch the tip on the soldering iron to the blade to provide a larger surface area to heat the pots quicker.  The next step is to ground the lugs on the pots.  For the tone pots, bend the center lug back until it is touching the pot casing.  You probably won’t get it all the way back, but get it as close as you can.  Now, solder the lug to the casing.  Be very careful that you don’t let any molten solder run down into the small holes in the pot casing.  This can kill the pot, or at the very least cause a “bump” in the action of the pot.  Do I need to tell you to test it to make sure the lug and casing have a good connection?  Didn’t think so.  🙂  For the volume pots, look at the pot so the three lugs are pointing down.  Bend the lug on the right backwards until it is touching the casing, just like tone pots.  Again, solder the lug to the casing.  Do this for both the neck and bridge volume pots.

Since I still had the blade tip on the soldering iron, next I created the ground loop between all of the pots.  I used a piece of insulated, not shielded, 22 gauge wire and cut it to size so it creates an arc around all four pots starting with the neck volume pot and ending with the bridge volume pot.  Strip the insulation from the wire at the ends, and in the two places in the middle where it will be soldered to the neck and bridge tone pots.  It’s perfectly acceptable to use a bare wire without any insulation as the ground loop wire.  Just make sure it’s tight, and can’t vibrate or move and short something out.  Since I don’t have the precision of the pre-made kits, I opted for some flexibility and used the insulated wire.  Once the ground wire is soldered to all the pots, use your multi-meter to make sure you have continuity from the back of each pot to the back of every other pot.

The last step is to solder the tone capacitors between the volume and tone pots.  Since this is delicate soldering work, I suggesting switching back to the fine point soldering tip.  Using the picture above of the pots on the template board, the tone caps go from the lower lug on the tone pots to the middle lug on volume pots.  Most capacitors don’t have any “directionality”, so it doesn’t matter which end goes on the tone pot or the volume pot.  When you’re done, you should have something that looks like this:

There you have it.  The switch and harness are wired, and ready to be installed in the guitar.  Next time we’ll finish off the electronics upgrade be installing the switch and soldering everything together.

Until next time, have another drink.  The more you drink, the better I sound.


Read Full Post »

I’ve been fortunate to have a little free time to work on the guitars. As my loyal readers know (all 3 of you), I replaced the nuts on the eBay guitar and the Epiphone, and then replaced the nut on the eBay guitar again to get a better finish. I also spent some time researching guitar electronics including tone capacitors and potentiometers.  Today, it is time to upgrade the electronics in the Epiphone with new caps, pots, switch and jack.

In my previous post, I decided on vintage New Old Stock Paper-In-Oil .015uF and .022uF capacitors.  As for potentiometers, CTS 550K +/-10% pots seem to be the gold standard.  I also ordered some 1950s style wire to make everything look authentic.  The caps were ordered from MartinSixStringCustoms.com and the matched set of CTS pots came from JonesyBlues.com.  The wire, switch, and jack, I got from Allparts.com.

There is a decision to be made at this point as to the “style” of wiring.  In the most basic sense, there is 50’s wiring and modern wiring.  As I understand it, 50’s wiring preserves the highs when you roll off the volume, but adjusting the tone can affect volume.  This is what was used in the 50’s and 60’s.  Modern wiring is considered more “stable” in that there is less interplay between the tone and volume pots, but the downside is that your tone can become “muddy” at lower volume levels.  I opted for 50’s wiring to preserve the highs at lower volumes.

Now that we have all the parts, and we have the schematics for the wiring (thanks again to the MyLesPaul forums) it’s time to actually perform surgery.  Everything up this point has been small, lightweight modifications.  If I screw this up, it’s definitely off to the guitar shop to have someone else fix my mistake.

Before we begin, I’d like to apologize for the lack of pictures in this posting.  I didn’t realize how involved removing the electronics would be, and I didn’t take make pictures.  I promise I’ll make up for it when we put things back together.

Step one is prepping the patient for surgery.  I recommend removing the strings, bridge and tailpiece, and covering the pickup covers.  I didn’t do it, and I ended up with small scratches on the pickup-covers where the strings rubbed.  Fortunately, the pups will be replaced soon, so I’m not too upset.  Next, flip the guitar over and remove the toggle switch cover and the electronics cavity cover.  This is what my Epi looked like when I took off the electronics cavity cover.

Disconnect the wiring harness and clip the zip tie to let the wiring float free.  Be careful not to nick or cut any of the wires when cutting the zip tie.

Also, we need to remove the ¼” jack plate.  Make sure you keep the switch and cavity cover screws separate from the jack plate screws.  They are different sizes.  Once the jack plate is off, remove the jack from the cover and slide the jack inside the guitar.

At this point, I opted to remove the electronics from the guitar to make it easier to de-solder the pickup leads from the pots.  Flip the guitar over again so you see the front of the guitar.  Carefully remove the knobs from the pots to expose the nuts and washers.  Remove the nuts from the pots and gently push the pots into the guitar.  While we have the guitar right-side-up, remove the nut holding the toggle switch in place.  Once the nut is off the switch, the rhythm/treble label may come off, too.  Now that the switch and all the pots are free, flip the guitar over so you see the electronics cavity again.

Carefully remove the electronics from the cavity making sure to not put too much tension on any wires leading into the guitar.  These are the wires leading to the pickups and the bridge ground; in other words, the wires we’ll keep.

It’s now time to fire up the soldering iron.  A few important tips to keep in mind:

  • Use at least a 40 watt soldering iron.  We are soldering (and de-soldering) wires from the back of the pots.  The pots are larger pieces of metal and therefore require more heat.  Using a lower wattage soldering iron will “cook” the inside of the pot and ruin it while you are trying to get it hot enough to melt the solder.
  • Make sure you have both a fine point and a blade tip for your soldering iron.  The fine tip is for the leads on the pots, and the blade is great for working the back of the pots.
  • If you’re new to soldering, there is a great video here to get you started.

Got that?  Good.

We need to identify the 5 wires we are going to de-solder.  They are the ground and lead wires from the neck and bridge pickups, and the ground wire from the bridge.  The pups wires are actually a wire within a wire (shielding), so don’t go looking for 5 separate wires, you’ll only find 3, but there are 5 places we need to de-solder.  On my Epi, the bridge pup wire was black with a white lead inside, and the neck pickup was red with a red lead inside.  The bridge ground was a single black wire.  Yours could be different.  I circled the bridge pup ground and lead in the picture below.  The neck pup ground and lead are soldered to the pot immediately to the right in the picture, but are obscured by the bundle of wires in the middle.  To orient yourself with the picture, the neck would be above the top of the picture, and the lower strap button would below the bottom of the picture, and you can see the jack plate in the lower left corner.

Once you have the wires de-soldered and because we already disconnected the clip and zip tie, the old harness should be completely free so you can put it off to the side.  Next, we need to remove the pickups by removing the 4 screws holding the mounting rings.  Since the pickup wires are no longer soldered to anything, the pups should come right out.  Again, keep the mounting ring screws separate from the other screws.  They are a different size.

With the pickups out, it should be easy to remove the switch.  Start by pulling the wire that goes to the switch out of the guitar until it is hanging out of the neck pickup hole, and then slowly work the switch out of the cavity, pulling the wire with it.

There you have it, a beautiful Epiphone Les Paul without a single piece of electronics in it.  At this point, it might not be a bad idea to take a break.  I know I need one!

Read Full Post »

Nut Job

I’d like to apologize to my loyal readers (both of you) for slacking on new posts.  My son was in the hospital and family came over for Thanksgiving dinner, so I was a little busy with family life.

I decided the first upgrade on the eBay guitar would be something relatively simple, and greatly needed.  I would replace the nut.  The old nut was obviously plastic, poorly cut, and had a nasty rattle to it.  A quick look at it and anyone could tell it was not crafted with the highest standards in mind.

Wow, what a train wreck of a nut.  First order of business is removing the old nut.  To ensure we don’t take off any of the finish when we remove the old nut, score along the edges with a razor blade.  This will cut through any glue binding the nut to the finish.  Take your time and be careful to not slice the guitar, but feel free to dig into the old nut.  It’s coming out and getting replaced anyway.

Next, lightly tap the nut to remove it from the slot.  On Les Paul style guitars, tap the nut from the fretboard side towards the headstock.  On Fender style guitars where the nut is in a groove on the fingerboard, tap it from the side and slide it out of the groove.  I like to use a flat-head screwdriver to tap a Fender nut out of the groove.  On Les Paul style axes, I use a large chisel turned upside down.  I like the wide surface area it provides, but make sure it’s upside down.  You don’t want to take any wood off the fretboard.  A couple of light taps on the chisel with a hammer and the nut should pop right out.

The original nut was worse than I thought.  It was a hollow piece of plastic, which is not good at all for transferring the sound from the strings to the guitar.  Also, it had entirely too much glue on it.  Cleaning up the slot was going to be a challenge.

To get an idea of how cheap the old nut was, here’s a side-by-side shot of the old nut and new Tusq nut.

I started by using a small chisel to remove the plastic still glued to the fingerboard.  Then, I used a small file to remove the remaining glue from the slot and fretboard edge.  It’s important to have good contact between the nut and the wood of the neck as this is one of the 2 or 3 places where the guitar gets its tone from the strings.  Make sure all the glue is out of the slot and the edge of the fretboard, and there is a good right angle between the slot and the fretboard, but try not to take any wood off the edge of the fingerboard since this will change the scale length and affect intonation.  You want it flat, for good contact between the wood and nut.

Now with the slot cleaned up, we’re ready for the new nut.  I’m using a Tusq pre-cut nut for an Epiphone Les Paul.  You can find them online for around $10.  Starting with a pre-cut nut helps speed the process along.  The eBay guitar neck has similar dimensions, so the Tusq nut was a good place to start.

I put the new nut in the slot to see how well it fits.  The new nut was a little thicker than the old nut, and much taller.  To shape the new nut to fit the slot, we sand the bottom and back (the flat sides) of the nut.  I started with 60 grit sandpaper because the nut had to be lowered quite a bit.  Once I had the nut close to the right size, I switched to 220 grit sandpaper to avoid taking too much off.  I can’t stress how important it is to make small changes and constantly recheck.  I’ll show you why in a few minutes.  Also, when sanding the nut down, it’s very easy to sand it out of square.  To avoid this, put the flat part of the nut you’re not sanding against something with a flat edge.  I use the edge of a level to keep the nut square while I’m sanding it.  Here I’m sanding the back of the nut while keeping the bottom on the level to keep everything square.

Most manufacturers give specifications of how high each string slot should be above the fretboard.  By putting the nut in the slot and using feeler gauges you can sand the nut to almost the right height.  If you don’t have feeler gauges, you can use the strings to get a close fit.  String up and tune the guitar.  Now, finger the strings individually at the first fret.  Look at the distance between the string and second fret.  This is the same distance the string should be from the first fret when the string leaves the nut.  Think of the nut as a zero fret.  Also, if the nut is too high, notes played on frets 1-5 will be very sharp.  It’s perfectly ok to play the guitar without the nut being glued in if you want to check tuning and intonation.

Once the nut is very close to the right height, each slot in the nut needs to be finished.  Pre-cut nuts are a great starting point, but the slots are not fully shaped.  For that, we need a set of small files.  I use very small wood files, or you can buy a set of files custom-made for finishing nuts from StewMac.  A few important details to keep in mind when working the slots.  First, the string should always slope from the fingerboard side down to the headstock side.  The nut should be the tallest and tightest where the string leaves the nut toward the bridge.  This keeps the string from vibrating in the nut causing unwanted buzzing and dampening the tone.  On the other hand, you don’t want to the slot to be too tight or it will bind the string.  This leads to the familiar “ping” of the string slipping while tuning, and will lead to tuning issues in general.

Now that we have the nut the right height and the slots finished, we want to sand the sides to have a nice feel and finish.  On most Les Paul style guitars, the base of the nut closer to the headstock is ever so slightly wider than the side against the fingerboard.  This is where I made my sanding mistake.  Things were getting late, and I tried to hurry up by using the 60 grit sandpaper.  I ended up taking a little too much off the low E side of the nut, and I still had to finish the sides with 220 grit.  I made the nut narrower than the neck.  It shouldn’t affect tone or playability, but it doesn’t look like a quality job.  I’ll be making a new one soon.

Even from just a few short minutes playing the guitar, I can tell it has a brighter tone and better sustain.  The sound seems fuller with more harmonics coming out with each note.  Overall, it’s well worth the $10 for the new nut.  If you’re doing your first nut job, I strongly suggest buying 2 nuts in case you mess one up.  Installing a new nut is not difficult, but having the safety net of a fallback is always nice.  I did this when I put a new nut in the Epiphone, and I’m glad I did.  I made a mistake and filed one of the string slots too much.  Fortunately, I had a second nut.  I took my time on the second one, and it come out beautifully.

Until next time, have another drink.  The more you drink, the better I sound. 🙂

Read Full Post »

It’s here!  After waiting all day yesterday and peering out the window countless times (my neighbors must think I’m becoming a reverse peeping Tom) to see if a big brown truck is in the driveway , my eBay prize arrived around 7 PM.  Ok, that may be a bit of an overstatement.  I mean, really, how much of a prize can a $135 guitar be?  Well, in a nutshell, not much.  I was hoping for a good deal by paying only $135 for a guitar, instead what I got was barely a $135 guitar.  This feels more suited for playing Guitar Hero than serious playing guitar.  I stayed up until 2 AM looking, playing, and dissecting the guitar, and at every step I became more and more dejected.  The body was too light, meaning the quality of the wood was only slightly above balsa (oh, how I was wrong).  The truss rod was covered over by a block of wood to mount the truss rod cover meaning very shoddy workmanship.
Here are some pictures of the eBay guitar:
* Notice the hole cut into the body leaving nothing but the balsa wood veneer between the pot and the knob

After carefully evaluating the pieces of the guitar that would be left intact after my conversion, I decided the quality of what would be left just wasn’t worth it.  I felt like a kid at Christmas who for months has asked for a Han Solo action figure only to unwrap the deluxe version of Jar Jar Binks.  In the midst of my depression I realized I was too tired to commit hari kari, so I went to bed instead.

This morning I awoke with a fresh perspective.  So I was out $135; it’s not the end of the world.  I could get some of that back by selling the guitar on Craigslist.  After I do a little work on it like replacing the nut and setting it up right, it would make a great first guitar for some kid whose parents didn’t want to spend a lot of money.  I figure either it will be played to death, or end up in the closet like most guitars owned by 12 year olds, but I will make sure it’s a playable instrument before I sell it.  Also, in the process of making it playable, it will fulfill some of its initial purpose, which is to help me hone the skills I need to maintain my other axes.  Whew, I don’t feel so bad now.

So now I was stuck in the same situation as before.  I needed a guitar as the base for my project, but I didn’t possess anything suitable that I wanted to use.  I decided to not make the same mistake twice, and concluded I would see and play the guitar first hand before I bought it.  As a side note, I never understood people who made the same mistake twice.  There are so many new and wonderful mistakes for us to make in our lives, why waste time making the same mistakes?  I tell these people to expand their horizons and start making new and exciting mistakes.  It makes my life seem less chaotic.
“Good judgement comes from experience. Experience comes from poor judgement” – Unknown
Anyway, I digress.  I searched Craigslist for a suitable guitar.  Nothing.  I tried the eBay route before and it didn’t work out well, so I skipped that option.  Oh what to do!  I remembered that Guitar Center sold used gear.  I would probably pay a little more than I wanted, but at least I would know what I’m buying.  Heaven smiled upon me as my local GC had an ’08 Epiphone Les Paul Standard Plain Top for $250, and it included a hard shell case to boot!  After dropping my son off at daycare, and before my afternoon of non-stop conference calls began, I hurried over to GC to check out the axe.  I’m not a big fan of burst styling on guitars, but this one was a very nice Heritage Sunburst with a great grain.

Here it is, the base for what I’m now calling my Gibsophone Faux Paul project.

Now that I have a decent guitar to start with, it’s time to play the guitar a little and figure out what modification I should make first.  Stay tuned and I’ll let you know what I decide.  Until then, I have a “new” guitar to play.  Woo hoo!

Read Full Post »

So I picked up a Les Paul copy from eBay for $135 the other night.  I’m not entirely sure what make or model it is, and neither was the seller.  When he got the guitar the headstock was blank, so he added a Gibson diamond logo and the Gibson script name (for aesthetics).  The seller was up front about the fact the guitar was not a Gibson, and he was kind enough to post a YouTube video of him playing the guitar, so at least I have a rough idea of what it sounds like, not that it matters, though.  At this point any guitar player is saying “What?  You bought a guitar and you don’t care what it sounds like?  Either this guy is doesn’t know what he doing, or he’s simply off his rocker.”  Well, I may not be able to argue the second half of that statement, but I do have some idea what I’m doing.

I’ve been wanting a “project guitar” for a while.  Something I can work on, fuss with, and generally modify without worrying about screwing it up too much.  I’ve been wanting a Gibson Les Paul, too.  I figured I’d try my hand at seeing if I could come close to recreating a vintage Les Paul using an inexpensive body and replacing pretty much everything else with authentic Gibson parts.  Now you can see why I’m not overly concerned about how the guitar I bought on eBay sounds.

As I sit eagerly awaiting the arrival of my eBay prize, I figured it would be a good idea to put together a plan of what I’m going to do to the guitar.  Here’s my list in order of priority:

  1. Swap out pickups for a pair of Gibson Burstbucker 1/2, Gibson 490R/498T, or a matched set of Gibson ’57 Classics.
  2. Replace the electronics.  Probably with Bumblebee PIO caps and either CTS or Gibson pots.
  3. Replace the TOM tailpiece/bridge with a rolling bridge and Bigsby tremolo.
  4. Replace the tuners with either Kluson or Grover tuners.

* I may have to swap items 1 and 2 because the description of the guitar on eBay mentioned there’s a problem with bridge pickup volume pot.  We’ll have to see what kind of condition it’s in once the guitar gets here.

So that’s the plan.  I’ll post pickup specs, wiring diagrams, pictures, and any other bits of information as I research the parts to make my “Faux Paul”.

Read Full Post »

I have GAS

My wife says I have GAS.  I think she’s right.  No, she doesn’t mean I overly produce mass quantities of the smelly stuff that can clear a room.  If not that, then what exactly is GAS, you may ask?  It’s Guitar Acquisition Syndrome (full disclosure – A guy at work came up with the term GAS.  I can’t take credit for it.)  Anyway, I’m addicted to guitars.  I had 8; now I have 9.  I just acquired what I think is an Epiphone Les Paul off of eBay.  I’m not entirely sure what it is, and neither was the seller.  More on that later…

While my collection may seem modest by some standards, I can assure you my wife would consider it to be more than adequate, possibly verging on the extreme.  I think the same of her shoe collection, but we love each other in spite of our little eccentricities, so it’s all good.  Anyway, I’m not a professional musician.  Far from it, in fact.  I’m just a guy who’s been playing bass on and off for 25 years in assorted bar bands, and only started seriously playing guitar two and half years ago.  By seriously, I mean I joined a band who plays for free once a month, 5 months a year.  Not exactly what you’d call a “working musician.”  🙂

Here’s what I’ve got at the moment:

  • Washburn Raven – This originally was my sister’s guitar.  Somehow over the course of time it migrated from her room to mine, and eventually became “my guitar.”
  • Kramer Striker Bass – My first bass.  It served me well all through high school and my first 6 bands.
  • Fender Precision Bass – I got this right after band #7 broke up because we all graduated college and I moved to Atlanta.  Haven’t played bass in a working band since.  Go figure.
  • Yamaha Classical – My loving wife got this for me when I told her I wanted an acoustic guitar to take to the boat.  She’s not into guitars so she didn’t know the difference.  Still, she’s a wonderful woman for buying me one.
  • Fender California Acoustic – I picked this up to take to the boat.  I love my wife dearly, but trying to play a classical guitar in a folk style just doesn’t work, so the Yamaha became decoration.
  • Fender “Fat” Stratocaster – After joining my current band as the rhythm guitar player and using the Washburn for the first couple of gigs, I thought it was time to get myself a decent electric.  This is my favorite guitar right now.
  • Stewart Stow-Away – I travel for my job.  The Stewart is the perfect travel guitar for me.  If you’ve never seen one, head over to http://www.stewartguitars.com.  It looks like a Strat, plays like a Strat, and sounds like a Strat.  It’s an awesome guitar that fits inside a standard roll-aboard suitcase.  Very cool.
  • Martin Acoustic – The Fender acoustic is nice, but the tone of the Martin is spectacular.  What an amazing full, warm, rich sound.  My current band had been together for 2 years, so I figured it was a safe bet that I would be gigging with this axe.
  • The Les Paul I bought on eBay – The reason I decided to start this blog.

So, what’s the deal with the Les Paul from eBay?  Well, I wanted a project guitar.  Something I could tweak and play with without worrying about screwing up a “good” guitar.  I didn’t want to do major surgery on any of my existing guitars for various reasons ranging from sentimental (my wife bought it, or it’s been in the family for 30 years) to rational (it’s the main axe when I play out).

Thus begins my winter project – turning a $135 guitar from eBay into of a copy of a 1960 Les Paul custom with a Bigsby tremolo.  The end result is what I’m calling my “Faux Paul.”

Stay tuned for updates, pictures, and sound clips as I do my best modifying the guitar.

Read Full Post »